retaining ring
英 [rɪˈteɪnɪŋ rɪŋ]
美 [rɪˈteɪnɪŋ rɪŋ]
网络 扣环; 扁丝卡簧; 挡圈; 固定环; 定位环
双语例句
- The flicked liquid metal is retained by the annular and tapered cushioning and retaining ring to drop on the metal collecting tray and flow into a metal cooling trough for aggregation.
甩出的液态金属被环锥形缓冲阻挡圈阻挡，落入金属收集盘并流入金属冷却槽聚集。 - Loosen scale retaining ring and remove turn indicator assembly. It is not necessary to change the memory set point.
松开刻度固定环，拆卸旋转指示器总成。不需要改变记忆设置点。 - The device is mainly made up of inner tube, outer tube, piston tube, end cover, retaining ring, hanger, liquid-route element and sealing element.
该装置主体由内管、外管、活塞管、端盖、承压环、吊耳、液路元件和密封元件等组成。 - Retrofit retaining ring on transmission.
改装变速器的扣环。 - If that retaining ring is misaligned, a bullet could conceivably jam in the barrel.
如果扣环没有位移子弹会堵塞在枪桶里。 - To meet the requirements of new assembly procedures of wheel sets, the wheel tyre retaining ring roller mills for locomotives were developed. Third, tread and wheel rim will be abraded.
为适应轮对新的组装工艺要求，研制了机车轮箍扣环滚压机。恢复踏面和轮缘的线型时，需要对车轮进行车削修整，导致轮箍与轮缘变薄。 - Analytical solution of residual stress at inflexion of retaining ring moves outside
两炮成形强化护环拐点外移时残余应力的解析解 - Loosen the scale retaining ring and rotate the turn indicator scale to align with the "0" on the handwheel.
松开刻度上的固定环，旋转指示器刻度使其对齐手轮上的“0”。 - Clean contact surface for retaining ring on the transmission.
清洁变速器的扣环接触面。 - Application of F-12 Aramid Fiber in Retaining Ring of High-speed Generator Rotor
高速电机转子用F-12芳纶/环氧复合材料护环的研究 - Pressure Seal? uncomplicated design has segmented retaining ring and mild steel silver plated gasket to aid disassembly and provide maximum bonnet seal.
压力密封？结构简单，分段扣环，镀银低碳钢垫圈，有助于拆卸和最大限度的阀帽密封。 - Brick retaining ring is functioned as a stopper for axial sliding of lining bricks and increasing the rigidity of kiln shell.
挡砖圈具有阻挡砖的轴向滑动和增加筒体刚度的作用。 - The Research on Microstructure and Its Properties of Retaining Ring Material s
护环的组织与性能研究 - There is a high macro residual stress in retaining ring.
护环的宏观残余应力不允许用回火方法去除，高的回火温度会损失护环的力学性能指标。 - Test and research on new hydraulic bulging device for retaining ring
护环液压胀形新装置的试验研究 - So we have to invent a new method for relieving the macro residual stress in retaining ring.
实验结束后，用切应力环的办法测量宏观残余应力，用大千分尺测量护环环口直径的变化。 - The method for the calculation and monitoring of contracting force at small retaining ring in QFS-60-2 double-water inside cooling generator was raised and the necessity of monitoring of contracting force was discussed.
提出了对QFS602型双水内冷发电机转子小护环紧力的计算方法及监测方法，并论述了监测的必要性。 - Stress Determination about Heat Sleeve of Rotor Retaining Ring in Large Turbogenerator
大型汽轮发电机转子护环热套应力测试技术研究 - In this paper, the method of pulsating hydraulic test to relief retaining ring residual stress is introduced.
本文介绍了用油压脉动试验的方法去除护环的宏观残余应力。 - Researching the statics and dynamics of the locomotive wheel added retaining ring.
对加装扣环的机车轮对的静、动力学行为进行了研究。 - The technique and its principle of high temperature strain measurement are introduced to determine heat sleeve stress about rotor retaining ring of large turbogenerator.
本文简要介绍了高温应变测量原理和技术在大型汽轮发电机转子护环热套应力测试中的成功应用。 - This article has described expanding method for repairing the concave retaining ring caused by the hydraulic bulging.
详细介绍了用扩冲法对液压胀形出现凹形的护环进行修复的方法。 - Mechanical Analysis and Calculation for the Influence of the End Friction on Shape of Retaining Ring when Being Expanded
护环胀形时端部摩擦力对护环形状影响的力学分析计算 - Based on the defect characteristics introduced by stress of generator retaining ring, the parameters for ultrasonic examination are selected, and the typical defect waveforms are analyzed, from which some worth noticeable points are pointed out.
文章根据发电机护环的应力特点和由此导致的缺陷特征对超声波探伤的参数进行了选择，并对典型缺陷波形进行了分析，指出了发电机护环超声波探伤时应注意的事项。 - The retaining ring is an important component of turbo generator.
护环是汽轮发电机的重要部件。 - Effects of ion implantation with rare-earth erbium and chromium on SCC behaviour for generator retaining ring steel
稀土铒和铬离子注入对电机护环钢SCC性能的影响 - Building the optimization model by the suppose to quest the theory high-point borderline of the adding retaining ring wheel.
由此假说建立优化模型，寻求到加装扣环轮对的理论极限边界。 - The research result shows that the presence of the retaining ring trough has some effect to the statics and dynamics, but the effect is local and does not cause the change of the quality.
研究结果表明扣环槽的存在对轮对静、动力学行为产生了一定影响，但这些影响是局部的，并没有引起质的变化。 - Focusing on the retaining ring mandrel reaming process in the hot forging, we test and study on the scaled test model simplification.
针对护环热锻中芯棒扩孔工艺，采用简化缩比试验模型进行了试验研究。